Thickness according to ASTM D3767

Measurement of the thickness of the glove materials at the finger and palm.

Palm: 0.05mm min.

Exceeded

Finger: 0.05mm min.

Exceeded

Length according to ASTM D3767

Measurement of the total length of the glove

230mm min.

Exceeded

Elongation according to ASTM D412

Measurement of the stretchability of the material. This test shows the breaking point of the material when it is stretched.

Before Aging: 500%

Exceeded

After Aging: 400%

Exceeded

Tensile Strength according to ASTM D412

Measurement of the amount of force applied to the material before it breaks. The higher tensile strength the greater force it takes to break a material of the same thickness.

Before Aging: 14 MPa

Exceeded

After Aging: 14 MPa

Exceeded

Water Leak according to ASTM D5151

Uses a water leak test to determine the amount of holes in gloves. The lower the AQL level the better quality of gloves.

AQL: 2.5

Exceeded

Powder Residue according to ASTM 6124

Determines the amount of residual powder on the glove material. A powder-free glove should have less than the ASTM minimum to be able to meet the standard.

< 2 mg

Exceeded

Thickness according to ASTM D3767

Measurement of the thickness of the glove materials at the finger and palm.

Palm: 0.08mm min.

Exceeded

Finger: 0.08mm min.

Exceeded

Length according to ASTM D3767

Measurement of the total length of the glove

230mm min.

Exceeded

Elongation according to ASTM D412

Measurement of the stretchability of the material. This test shows the breaking point of the material when it is stretched.

Before Aging: 300%

Exceeded

After Aging: 250%

Exceeded

Tensile Strength according to ASTM D412

Measurement of the amount of force applied to the material before it breaks. The higher tensile strength the greater force it takes to break a material of the same thickness.

Before Aging: 11 MPa

Exceeded

After Aging: 9 MPa

Exceeded

Water Leak according to ASTM D5151

Uses a water leak test to determine the amount of holes in gloves. The lower the AQL level the better quality of gloves.

AQL: 2.5

Exceeded

Powder Residue according to ASTM 6124

Determines the amount of residual powder on the glove material. A powder-free glove should have less than the ASTM minimum to be able to meet the standard.

< 2 mg

Exceeded

Thickness according to ASTM 3767

Measurement of the thickness of the glove materials at the finger and palm.

Palm: 0.08mm min.

Exceeded

Finger: 0.05mm min.

Exceeded

Length according to ASTM 3767

Measurement of the total length of the glove

230mm min.

Exceeded

Elongation according to ASTM D412

Measurement of the stretchability of the material. This test shows the breaking point of the material when it is stretched.

Before Aging: 650%

Exceeded

After Aging: 500%

Exceeded

Tensile Strength according to ASTM D412

Measurement of the amount of force applied to the material before it breaks. The higher tensile strength the greater force it takes to break a material of the same thickness.

Before Aging: 18 MPa

Exceeded

After Aging: 14 MPa

Exceeded

Water Leak according to ASTM D5151

Uses a water leak test to determine the amount of holes in gloves. The lower the AQL level the better quality of gloves.

AQL: 2.5

Exceeded

Powder Residue according to ASTM 6124

Determines the amount of residual powder on the glove material. A powder-free glove should have less than the ASTM minimum to be able to meet the standard.

<2 mg

Exceeded

Viral Penetration according to ASTM F1671

Measurement of the resistance of the glove material to potentially infectious body fluids breaking through the material.

Pass

Pass

Chemotherapy Drug Permeation according to ASTM D6978

Measure the time it takes for a chemotherapy agent to permeate through the glove material.

Pass

This glove has been tested for Chemotherapy Drugs as per ASTM D6978. Details for chemicals tested are available upon request.